How do you set the time on a Lathem clock?

To set the time:

  1. Remove the top cover.
  2. Press and hold the DATE/TIME button for 3 seconds.
  3. When the 7500E beeps, release the DATE/TIME.
  4. Push the DATE/TIME button and position the Indicator Mark next to the TIME.
  5. Press CHANGE to set the Hour.
  6. Press SET to save the change.
  7. Press CHANGE to set the Minutes.

How do you set the time on a Lathem 2121?

  1. Mount Clock in Suitable Location.
  2. Unlock and Remove the Cover.
  3. Lift the Type Section.
  4. Set the Printed Day and Time.
  5. Set Hands on Clock Face.
  6. Advance Print Wheels and Hands.
  7. Lower the Type Section into Place.
  8. Test that Clock Is Now Set Correctly.

How do I change the time on my Lathem atomic time 1600E?

What To Do If the Time Jumps One Hour On The 1600E

  1. Remove the top cover from the clock.
  2. Press the SELECT button and position the. mark at the “TIME ZONE”.
  3. Press the CHANGE button to select the correct time zone listed in the image below.
  4. After you finish setting the time zone, press the SET button once again.

How do I change the time on my Lathem 7000E?

To set the time:

  1. Insert the key into the Top Cover and turn it 1/4 turn to unlock the cover.
  2. By holding the left and right sides, lift the Top Cover up.
  3. Press and hold the DATE/TIME button for 3 seconds.
  4. When the 7000E beeps, release the DATE/TIME.

How do you set the time on a Lathem 400E clock?

To set the time on the 400E Time Clock:

  1. Place the clock in programming mode by using the included key to remove the top cover and flip the switch on the left to “Programming Mode”(to the right).
  2. When P1 is displayed on the screen, press Enter.
  3. Press + or – until the number on the lower left shows 7.
  4. Press Enter.

How do you change the time on a Lathem atomic time 1500E?

To set the time on the 1500E:

  1. Insert the key into the Top Cover and turn it 1/4 turn to unlock the cover.
  2. By holding the left and right sides, lift the Top Cover up.
  3. Press Select.
  4. If a password is set, enter the password.
  5. Press Select to position the Indicator Mark under Time.
  6. Press CHANGE to change the hour.
  7. Press SET.

How do I reset my Lathem Time 1500E?

To reset the 1500E:

  1. Insert the key into Top Cover.
  2. Turn the Key 1/4 turn to unlock the cover.
  3. By holding the left and right sides, lift the Top Cover up.
  4. Locate the Reset Switch on the left side of the time recorder.
  5. Using a pointed object, such as a pencil, press the Reset Switch.

How do you clean a Lathem clock?

With the time clock turned “On”, fold over a paper towel twice and dampen it lightly with Isopropyl Alcohol. Insert the damp paper towel between the print head and actuator and swipe the paper towel from side to side to clean the print head. Repeat this process until the desired print quality is obtained.

How do I setup my Lathem 400E?

How do I reset my Lathem atomic time?

How To Perform A Reset On A 7500E

  1. Insert the key into the Top Cover and turn it 1/4 turn to unlock the cover.
  2. By holding the left and right sides, lift the Top Cover up.
  3. Press and hold the DATE/TIME and CHANGE.
  4. Press and release the Reset Switch.
  5. When the 7500E display goes blank, release the DATE/TIME and CHANGE.

How do you change the ribbon on a Lathem 7500E?

To change the ribbon:

  1. Remove the top cover.
  2. Hold the Ribbon by its handle.
  3. Pull the Ribbon Up and Out of the 7500E.
  4. Place the new ribbon inside the 7500E, within the clasps that hold the ribbon into place.
  5. Make sure the ribbon is threaded between the Print Head and Ribbon Mask.